A pendant light in the wrong size is the fastest way to make a good room feel off — too small and it disappears, too large and it crowds everything under it. This pendant light size guide gives you the actual numbers: how wide a shade to choose and how high to hang it over a kitchen island, a dining table, and an entryway, in both inches and centimeters. No guesswork, no design jargon.
Every choice comes down to two numbers: the diameter of the shade and the hanging height — the gap from the bottom of the shade to the surface below it. Diameter controls how the fixture reads in the room. Hanging height controls whether people can see across the table, sit without ducking, and walk under it safely. Our 3D-printed shades, like the ECLIPSE, run from 7 inches (18 cm) to 12.5 inches (32 cm) across, which covers most single- and multi-pendant setups.
Over an island, use a row of two or three evenly spaced pendants rather than one. The combined width of the shades should equal about one-half to two-thirds of the island's length. Leave 6 to 12 inches (15–30 cm) of clear space at each end, and space the pendants 24 to 30 inches (61–76 cm) apart, measured center to center.
| Island length | Number of pendants | Diameter each |
|---|---|---|
| 4 ft (122 cm) | 2 | 7–9 in (18–23 cm) |
| 5 ft (152 cm) | 2 | 8–10 in (20–25 cm) |
| 6 ft (183 cm) | 2–3 | 9–12 in (23–30 cm) |
| 7–8 ft (213–244 cm) | 3 | 9–12 in (23–30 cm) |
Hang the bottom of each shade 30 to 36 inches (76–91 cm) above the countertop. That keeps the bulb out of sightlines while pooling light on the work surface.
The goal at a dining table is to light a span roughly one-half to two-thirds of the table's length. A single wide shade suits a small round or square table; a row of two or three shades suits anything longer than about 48 inches (122 cm). Because our shades top out at 12.5 inches (32 cm), longer tables look best with a cluster or a straight row rather than one oversized fixture.
| Table length | Recommended setup |
|---|---|
| Round, up to 42 in (107 cm) | 1 shade, 9–12.5 in (23–32 cm) |
| 48–60 in (122–152 cm) | 2 shades, 8–10 in (20–25 cm) each |
| 66–84 in (168–213 cm) | 3 shades, 9–12 in (23–30 cm) each |
Hang the bottom of the shade 28 to 34 inches (71–86 cm) above the tabletop with a standard 8-foot ceiling. For every additional foot of ceiling height, raise the fixture about 3 inches (8 cm).
For an entry, there is a simple starting formula: add the room's length and width in feet, and use that sum as the shade diameter in inches.
| Room size | Length + width | Target diameter |
|---|---|---|
| 8 × 10 ft | 18 | ~18 in (46 cm) |
| 10 × 12 ft | 22 | ~22 in (56 cm) |
| 12 × 14 ft | 26 | ~26 in (66 cm) |
Since a single printed shade maxes out near 12.5 inches, hit larger targets with a tight cluster of two or three shades. In a standard-height entry, keep the bottom of the fixture at least 7 feet (213 cm) above the floor. In a two-story foyer, center the pendant in the window if there is one, and never let it hang below the second-floor landing. If it hangs over a console table, treat it like a dining pendant and center it on the tabletop.
| Location | Bottom of shade above surface |
|---|---|
| Kitchen island or counter | 30–36 in (76–91 cm) above the counter |
| Dining table (8 ft ceiling) | 28–34 in (71–86 cm) above the table |
| Walkways and open floor | at least 84 in (213 cm) above the floor |
The one adjustment to remember: add about 3 inches of drop for every foot your ceiling rises above 8 feet, so the fixture stays in proportion with the taller room.
When you just need a starting point for a single ambient pendant in any room, add the room's length and width in feet and read the total as inches of diameter. A 10-by-13-foot room lands around 23 inches — which, in our line, means a cluster of two or three shades rather than one. From there, adjust down if the fixture will hang over furniture and up if the ceiling is high.
Once you have your numbers, the fun part is choosing a shape. Browse the full range of shades and cord kits in our Pendant & Ceiling Lights collection, or add a smaller accent with a piece from our Table & Desk Lamps collection. Every shade is made to order in our Connecticut studio in more than 50 colors.
If your island, table, or ceiling is an unusual size, we can print a shade to your exact dimensions — that is the advantage of a one-person studio. See how it works on our Custom 3D Printing page, send us your measurements, and we will size the shade to fit the room instead of asking the room to fit the shade.
The KICK is a full-size (regulation size 5) airless soccer ball, 3D printed as an open lattice in durable TPU. It compresses on impact and springs right back — no pump, no air, and it can never go flat. Weatherproof and UV-resistant for grass, turf, or hardcourt, with a bold modern look and a consistent, controlled bounce.
• Black, White, Clear, or Blue — plus 50+ custom finishes on request (see the color chart here).
• Standard — cleanly printed and ready to play, at the friendliest price.
• Premium — printed slower in finer layers for a smoother, cleaner lattice. Choose it for gifts or your finest finish.
• No pump, no needle — it never goes flat
• Open-lattice TPU compresses on impact and springs back
• Weatherproof and UV-resistant — grass, turf, or hardcourt
• Slightly firmer than a traditional air-filled ball
• A standout gift for soccer players, coaches, and training
• Great for backyard, practice, and skills work
• Rinse clean with water as needed
• Designed and made in-house by DrMaker3D
• Every ball is inspected before shipping — damaged or not as described? Contact us within 30 days and we'll make it right.
• 30-day free returns — if it isn’t right for you, email us for a prepaid return label.
Each ball is 3D printed to order and inspected by DrMaker3D before it ships — a small Connecticut studio, not a factory.
I purchased the airless soccer ball for my son and we are very pleased with the item. We have had it for a couple of weeks now and it has held up great, very durable. The customer service was top notch as well. This was my first time purchasing a 3D printed item and I was unsure of the quality but I am very happy with the item I received.
Elisa · Jun 2025
Reviews collected from our Etsy shop, where DrMaker3D has been selling since 2025. Every one is from a verified purchase.
